Independent study aid. Not affiliated with or endorsed by NCEES. Always verify against the current NCEES exam specifications and reference handbook.

PE WRE Learning Hub · PE Civil: Water Resources and Environmental · Area 4 of 12

Analysis and Design — PE WRE

Topic video on its way — a detailed walkthrough of Analysis and Design, with animations and worked examples.

Watch the topic: the detailed video walkthrough of Analysis and Design will sit here.

Take the 3-question mini-quiz ↓

Mass balance

Write the balance before reaching for a process formula: accumulation = in − out + generation − consumption. At steady state with a conservative substance, two joining streams mix to the flow-weighted average concentration. For a reacting substance the same balance, applied to a completely mixed vessel, produces the reactor equations used across the treatment areas. Flow measurement — weirs, flumes and meters — supplies the Q that every balance needs; a sharp-crested weir turns a measured head into a flow.

Steady mixing: C = (Q1C1 + Q2C2)/(Q1 + Q2)  ·  Load (lb/d) = Q (MGD) × C (mg/L) × 8.34

Worked example Mixing two waste streams

Given: A plant receives 2.0 MGD at 200 mg/L BOD and 0.5 MGD at 50 mg/L BOD. Find the blended BOD concentration.

Solution:

  1. Mass in, in flow × concentration units: 2.0 × 200 + 0.5 × 50 = 400 + 25 = 425.
  2. Total flow: 2.0 + 0.5 = 2.5 MGD.
  3. C = 425 / 2.5 = 170 mg/L.

Answer: Blended BOD = 170 mg/L.

Hydraulic loading

Hydraulic loading rates size surface-driven processes. The surface overflow rate of a clarifier is SOR = Q/A — the upward velocity the flow would have if it rose evenly through the tank — and a particle settles out only if its settling velocity exceeds it. Detention time, θ = V/Q, sizes volume-driven processes, and weir loading, Q per unit length of weir, checks that the exit flow does not drag solids over the launder.

SOR = Q/A  ·  θ = V/Q  ·  Weir loading = Q / weir length

Worked example Clarifier surface overflow rate

Given: A circular clarifier 80 ft in diameter receives 2.0 MGD. Find the surface overflow rate.

Solution:

  1. Area A = π × 40² = 5,027 ft².
  2. SOR = 2,000,000 gal/day / 5,027 ft² = 398 gal/day/ft².

Answer: SOR ≈ 398 gpd/ft².

Solids loading

A clarifier can pass its hydraulic check and still fail on solids: the solids loading rate applies the solids flux — flow times concentration — to the same surface area. In an activated-sludge secondary clarifier the flux uses the combined flow (plant flow plus return sludge) at the mixed-liquor concentration. The 8.34 factor converts MGD × mg/L into lb/day; forgetting the return flow in the numerator is the classic error.

Solids loading = (Q + Qr) × MLSS × 8.34 / A  (lb/day/ft², flows in MGD)

Worked example Solids loading on a secondary clarifier

Given: A clarifier of area 2,000 ft² receives plant flow of 1.0 MGD (neglect return flow for this check) at MLSS 2,000 mg/L. Find the solids loading rate.

Solution:

  1. Solids applied: 1.0 × 2,000 × 8.34 = 16,680 lb/day.
  2. Divide by area: 16,680 / 2,000 = 8.34 lb/day/ft².

Answer: Solids loading = 8.34 lb/day/ft².

3-question mini-quiz

Analysis and Design

Choose your answer, then check it to see the result and explanation.

1. A tank of volume 500,000 gal receives 1.0 MGD. Its hydraulic detention time is:

2. The load carried by 2.0 MGD at 150 mg/L is:

3. A clarifier 60 ft in diameter has a weir around its full circumference. At 1.885 MGD the weir loading is closest to: (weir length = π × 60 = 188.5 ft)

Ready for the complete rehearsal?

Step up from this three-question taster to the full timed PE WRE simulation — 80 questions in exam conditions, with a per-area diagnostic.

Keep building exam speed

This whole hub is free — every area page, mini-quiz and podcast. When you are ready to rehearse under exam conditions, the separate PE WRE exam simulation runs the full 80 questions against the clock.

Preview the PE WRE exam simulation Open the exam simulator