Independent study aid. Not affiliated with or endorsed by NCEES. Always verify against the current NCEES exam specifications and reference handbook.

PE WRE Learning Hub · PE Civil: Water Resources and Environmental · Area 3 of 12

Materials — PE WRE

Topic video on its way — a detailed walkthrough of Materials, with animations and worked examples.

Watch the topic: the detailed video walkthrough of Materials will sit here.

Take the 3-question mini-quiz ↓

Soil classification and boring logs

The Unified Soil Classification System (USCS) first splits soils at the No. 200 sieve: more than half passing means a fine-grained soil, classified by liquid limit and plasticity index on the plasticity chart; more than half retained means coarse-grained, classified by gradation (Cu, Cc) and fines content. The A-line, PI = 0.73(LL − 20), separates clays (above) from silts (below). A boring log records the strata in order with SPT blow counts, moisture and the water table — exam questions ask you to pick the stratum or property the log actually shows.

A-line: PI = 0.73 × (LL − 20)  ·  Cu = D60/D10

Worked example Classifying a fine-grained soil

Given: A soil has 60% passing the No. 200 sieve, liquid limit LL = 45 and plasticity index PI = 25. Classify it under the USCS.

Solution:

  1. 60% passing the No. 200 sieve is more than half, so the soil is fine-grained.
  2. A-line at LL = 45: PI = 0.73 × (45 − 20) = 18.3. The soil's PI of 25 plots above the A-line, so it is a clay, not a silt.
  3. LL = 45 is below 50, so the symbol is low-plasticity: CL.

Answer: CL — a lean (low-plasticity) clay.

Soil properties: phase relations

Every soil is solids, water and air. The phase relations tie them together: void ratio e = Vv/Vs, porosity n = e/(1 + e), and dry unit weight γd = Gsγw/(1 + e). Rearranged, e = Gsγw/γd − 1, which is the fastest route from a measured dry density to a void ratio. Saturation connects moisture content to void ratio through wGs = Se.

e = Gsγw/γd − 1  ·  n = e/(1 + e)  ·  wGs = Se

Worked example Void ratio and porosity from dry density

Given: A soil has specific gravity Gs = 2.65 and dry unit weight γd = 100 lb/ft³. Find e and n. (γw = 62.4 lb/ft³.)

Solution:

  1. e = (2.65 × 62.4)/100 − 1 = 1.654 − 1 = 0.654.
  2. n = 0.654/(1 + 0.654) = 0.654/1.654 = 0.395.

Answer: e ≈ 0.65; porosity n ≈ 0.40 (40%).

Concrete, piping materials and test methods

Concrete strength is governed first by the water–cement ratio: more water per unit of cement means a weaker, more permeable paste, while workability is checked with the slump test and density–moisture of compacted soil with the Proctor test. Piping materials are matched to duty — ductile iron and steel for pressure and thrust, PVC and HDPE for corrosion resistance, concrete for large gravity sewers. Exam questions pair a material or test with the property it actually measures; a Proctor test gives optimum moisture and maximum dry density, never a strength.

w/c = weight of water / weight of cement  ·  Strength falls as w/c rises

Worked example Water–cement ratio

Given: A mix batch uses 300 lb of water and 600 lb of cement. Find the water–cement ratio and state its effect.

Solution:

  1. w/c = 300/600 = 0.50.
  2. A ratio of 0.50 is a moderate value: lowering it (with the same cement content) would raise strength and lower permeability; raising it would do the reverse.

Answer: w/c = 0.50 by weight.

3-question mini-quiz

Materials

Choose your answer, then check it to see the result and explanation.

1. A soil sample is 70% retained on the No. 200 sieve. Under the USCS it is first classified as:

2. A soil has void ratio e = 1.0. Its porosity is:

3. The Proctor compaction test determines:

Ready for the complete rehearsal?

Step up from this three-question taster to the full timed PE WRE simulation — 80 questions in exam conditions, with a per-area diagnostic.

Keep building exam speed

This whole hub is free — every area page, mini-quiz and podcast. When you are ready to rehearse under exam conditions, the separate PE WRE exam simulation runs the full 80 questions against the clock.

Preview the PE WRE exam simulation Open the exam simulator